Welcome to ScapeCrunch

We are ScapeCrunch, the place where planted aquarium hobbyists come to build relationships and support each other. When you're tired of doom scrolling, you've found your home here.

Social Feed

Noahspapa
I Donated 2026
Last reply · posted in Journals
Sharing my first 120P aquarium and hoping to obtain feedback and guidance as it progresses.

I purchased the ADA 120P tank, AFA stand, mat and ADA substrate set from AFA in San Francisco. The set cost approx $2,000 including shipping. The set arrived as a set of boxes on a pallet which was loaded into my garage by a local delivery service using a small fork lift. The delivery process took approximately 4 weeks.

The substrate set included one large bag of ADA power sand, the three ADA additives - bacter 100, tourmaline and super clear, five bags of Amazonia 2 regular, and two bags of Amazonia 2 powder.

The tank is 120 x 50 x 50 cm, so roughly 48” x 20” x 20” and holds approximately 80 gallons.

All items arrived in excellent condition. Helpers and I moved the items to the basement. The stand was easy to put together. Plywood based. Sturdy. I drilled some additional 4” holes in the left side and rear panels for access. I put down the mat, and added the tank.

I chose a chihiros 1200 wrgb2 pro light. I hung an IKEA adjustable rod holder over the tank to suspend the light from which has been working out well for my tanks.

For other mechanicals: these have evolved since initial setup
  • Oase BIomaseter 2 thermo 350 canister filter loaded up with seachem matrix, seachem matrix carbon and seachem purigen.
  • Cuboid aquatics UV disinfection unit.
  • Oase Biomaster 2 850 canister filter loaded up similar to 350 and with all pre filter stuff (outer housing, center pipe, pads) removed
  • Netlea pre filter
  • ARC small acrylic yugang horizontal reactor
  • five pound co2 tank
  • CO2 Art pro CO2 regulator
  • soft, gray silicone 16/22 hosing used throughout
  • two sets of quick disconnects for the hosing
  • Jardli glass Lily pipe outlets
  • Hydra aquatics stainless steel inflow with skimmer
  • some inexpensive motion sensing led panels for light within the cabinet
  • two kasa smart plug strips

I’ve attempted to include some photos here but they don’t seem to be being pulled in.


IMG_7604.webpIMG_7605.webpIMG_7606.webpIMG_7607.webpIMG_7608.webpIMG_7609.webp

The hardscape for the tank was selected collaboratively with the team at cuboid aquatics in Pipersville, PA. I became aware they carried a wide range of hardscape including the WIO product line and they were within driving distance (6 hours), so I drove down and spent the next day with them. They were well stocked and were incredible people! Their lead designer Maddie lead the effort. The design uses large WIO black venom and jade rocks to support a hefty set of Galapagos and WIO Centurian wood. I packed up the hardscape, brought it home and put together the current design. I chose the larger Galapagos pieces as I liked the dark highly contoured lines.

The design is a triangular layout as the tank will be viewed from the right side as well as the front and we wanted to keep that right side looking similar to the front.

The left side and rear are filled with the ADA substrate set. In two areas just in front of hardscape there are areas of substrate set where I intend to plant dwarf lilies and crypt spiralis tiger. The remainder of the front and right side uses WIO Everglades riverbed which includes tan sand, pebbles, twigs, leaves, and cones. I also added WIO black venom and jade pebbles and twigs.

My friend and I primarily used seachem epoxy to epoxy the hardscape together. It was easy to use. It does put off quite an odor. We also used a glue product call R6000 which seems to have worked out quite well. The tank has been in water for two weeks now. Some of the putty connected to wood has come loose. Best I can tell the R6000 joints are holding.



This is the current layout and you can see there is the normal whiteish “stuff” growing on some of the driftwood.

My friend and I filled the tank and started up the equipment to check for leaks and flow. We encountered a few small issues that were quickly resolved.

In 1-2 hours it was obvious there were loads of tannins in the water. I had read an article on cycling on 2hr that suggested turning off the equipment, letting the hardscape soak for 48 hours, draining, refilling and restarting, so this is what I did.

Once I had that new water……

Oh, water here comes from RO water normally remineralized with APT Sky up to a TDS of 100-120, however I had read that it’s best to make sure.KH is present to support the cycling process so this water was remineralized with APT Sky plus to a KH of 2-3.

To help boost the cycling process I started with Microbe-lift gel filter inoculation in both canisters, and Microbe-lift Nite-out and special blend products.

Water tests show that two weeks in I have high ammonia and nitrite. Tank is running with no light.

I did start up the co2 reactor as I’ve never used the horizontal yugang reactor and wanted to see what sort of co2 levels I could reach. I measured 40-50 ppm with the Hanna test set which is great and turned the co2 back off for now.

I will continue to monitor ammonia and nitrite near daily.

In the mean time I will be working on a planting plan.

Please get back to me with any comments, suggestions for sustainability, improvement, etc.
44 Replies · 5731 views
C
Last reply · posted in Fertilizing and Aquarium Chemistry
Has any one had any experience with Controsoil in an nitrate limited system? I'd like to color up my Rotala H'Ra more than it is now and have been keeping my NO3 at around, or slightly under 5PPM but still above 0 while slowing ramping up my lighting intensity so I don't knockout the balance of the system. I've got the usual nice salmon pink tips you usually get with this cultivar, but wouldn't mind getting it a bit more red as I continue to ramp up the light even brighter. I've read that in order to do so, you really need to get the NO3 to as close to 0PPM as possible (along with of course, bright light and optimal CO2). I'm just concerned about having hair algae exploding again, but this time from nutrient limitation after finally getting it under control for the opposite reason.

I know that Controsoil doesn't have anywhere near the same ammonium content as Amazonas, but was wondering if there was enough nitrate in it to sufficiently supply my H'Ra with NO3 through the roots so I could run the system close to 0PPM on NO3 without having to use root tabs. I'm getting conflicting info- some sources say there's effectively zero nitrogen content in Controsoil, but a video from Buce Plant on nitrate limited coloration specifically names UNS Controsoil as ideal for this method. Would be curious to see if anyone has any first hand experience, or has enough concrete info to settle this.
10 Replies · 136 views
ample
Last reply · posted in Lounge
Saw a couple of you guys fighting for your lives over on Reddit. Valiant effort, but it’s just not the space for this hobby. Reddit will always be an open forum catering to the lowest common denominator. Nobody wants to see what years of focused practice produce, and will write off any decent aquascape or skilled plant husbandry as either having “thousands of dollars to spend” or just gatekeeping and elitism. Just let them have it. There’s no meaningful discussion to be had over there anyway.
8 Replies · 95 views
JacksonL
I Donated 2026
Last reply · posted in Equipment Discussions
I wanted to share my experience so far with a cheap flow meter from Aliexpress.
I am generally a “you get what you pay for” aquarist, but I have taken a gamble due to circumstances. It is still early days, but it feels like it may have paid off.
Looking to add a flow meter to help tune my CO2 in a newly set up 130L tank, I searched far and wide for the different options. They were few and far between, most were for far larger flows than I needed and those that were appropriate were ridiculously expensive to get to Australia. So I went searching on the various Chinese discount sites and came across the LZB-3WB flow meters. They are cheap… real cheap. Less than $30 Australian landed, which made me nervous, but felt it was worth a shot at that price.
Not knowing what flow ranges I would need I ordered a 6-60ml/minute model.
After installing it, it was clearly too high of a range for my tank, but it did allow for some visibility while adjusting CO2. It was certainly better than a bubble counter.
Here is a picture of it action:
1774008536678.webp
As you can see, the reading is below the scale of the meter, but with a marker I could at least set a starting point as I adjusted my CO2 higher. Also the adjustment valve was useless, a tiny turn would shut the flow off or open it to max out the meter.
I ordered the below as a replacement:
1774008611064.webp

2.5-25ml/minute seems like a good range for my tank.
As a bonus the valve is better than most standard regulator needle valves. I can adjust the flow in increments of about 1ml/minute.
Below is the valve in action:
1774008809018.webp

They have been in service for 2 months total now, 1 month each, so still an early review. It has been a solid upgrade though and was an easy install. They come with big 8mm barbed fittings but they can be unscrewed to reveal 1/8 female threads that standard needle valves for aquariums fit. I have also got some 1/8 to push fit fittings that I am yet to install as I am heading away on holiday for 2 weeks soon and don’t want to make any changes for the house-sitters to potentially have to fix!
Pros: adjusting my CO2 was made so much easier by being able to see exactly how much of an increase I was making with each adjustment. Monitoring that the valve isn’t drifting has been easy also, a quick check of the meter tells me it is steady.
Cons: I doubt that the reading is accurate. This means little to me, as I am not using it for a calculation or comparison between tanks. As long as the reading is consistent, even if it is wrong, I am fine with that. Also, the max pressure is listed as 40psi. I am unsure if that is a failure or accuracy maximum. Again, it doesn’t affect me as I run a low regulator pressure due to using a reactor. If I were using a diffuser that needed a high pressure, it may make me nervous.
As always, with any cheap gear, your mileage may vary. But, I thought it was worth sharing as it may help those with limited access to flow meters of appropriate sizes. So far it is proving to be the second best $25 I have spent on this tank, second only to the super red bristlenose I have in the tank.
55 Replies · 4624 views
Art
Art
Staff member I Donated 2026 Founding Member
Last reply · posted in Forum News/Feedback
This is the future home for the announcements when someone obtains an achievement badge. Let the games begin!
2065 Replies · 84654 views
  • Like
Reactions: Kwyet
JCole
Last reply · posted in New to Planted Aquariums? Post Here
Hey everyone,

I'm Josh (JCole on most of the reef forums). I've been in the saltwater side of the hobby for over 20 years, mostly running Acropora-dominant systems. I'm officially getting out of reef keeping and converting my current tank to a planted freshwater tank. I'll be honest up front: I know almost nothing about planted tanks. So I figured the best move was to introduce myself, start a build thread, and beg for help LOL.

A little background so you know a bit about my previous addiction! :-)

For a long stretch, my main tank was a 150-gallon Acro tank plumbed to a sump, a 20-gallon chaeto refugium, and a frag tank out in the garage. I crashed it in late 2020, lost over 70 Acros, and kept about six. Rebuilt it and kept going.

1794500161411.webp
1794499237529.webp
1794499244365.webp
1794499254374.webp
1794499262941.webp
1794499274577.webp
1794499283775.webp
1794499298026.webp
1794499308857.webp
1794500278516.webp

I eventually outgrew the 150 with coral colonies and needed to upgrade. My next tank was a 480-gallon acrylic peninsula, 8'x4'x2', with a 300-gallon stock tank sump in the garage.

1794499646141.webp
1794499661797.webp
1794499747467.webp
1794500100108.webp
1794500354960.webp

The aquarium was a dream aquarium of mine, but with having a full time job running a company with 3 boys in travel ball baseball, it consumed all of my time and I just could not give the tank what it actually needed and deserved. I eventually reset it, built my own cement rock and shelves, and sold the whole system in early 2025.

1794500867450.webp



After that, I downsized to a Marineland 180 (72x24x24) in the same room. This is the tank I'm converting to freshwater.

1794501194278.webp

WHERE I'M AT RIGHT NOW
  • Tank: Marineland 180, 72x24x24, glass.
  • Goal: High-tech planted. CO2, good light, fertilizers, the whole thing.
  • Cleaning: Done. I stripped the tank and sump with bleach and muriatic acid to get all the coralline algae off. It's clean and ready for water.
  • Sump: My Trigger Triton 44 sump is already set up and staying. I'm not going canister right now.
  • Controller: I've run an Apex for about 8 years, and I also wrote my own Raspberry Pi controller app that talks to the Apex and my Kasa, Shelly, and Jebao gear.
  • Lights: I pulled the halides and kept the pendants. For now, each pendant has a 120V LED grow light bulb in it.
  • Substrate: I have 19 bags of CaribSea Eco-Complete Planted ready to go.
WHERE I NEED HELP AND FEEDBACK
  1. CO2 with a sump: I know a sump gasses off CO2. Since I'm keeping mine, what tips do you have to keep the loss down (lower the return, cover the sump, change the overflow, anything else)?
  2. CO2 control: I can run a solenoid and a pH probe off the Apex or my own app. Do you control CO2 by pH, by a timer, or both? Is a drop checker still the thing to trust? And what do you use to actually get the CO2 into 180 gallons—an inline reactor on the return or diffusers? What safeguards do you run so a stuck solenoid doesn't gas the fish overnight?
  3. Lighting: Are LED grow bulbs in the pendants enough for a high-tech 72" long, 24" deep tank, or is that a stopgap? If I upgrade, what would you put over it?
  4. Substrate and hardscape: I read that people put lava rock in filter bags on the bottom to build up hills and slopes so the deep rooting plants get more depth. Is that the way to do it, and how deep should the Eco-Complete be on top? Is 19 bags enough for what I'm trying to do?
  5. Fertilizers: EI or lean dosing for a first-timer? I'm used to dosing two-part and testing a lot, so numbers do not scare me.
  6. Plants and fish: I want to start with beginner plants, but I'm not scared to try the harder stuff. Acros taught me patience, so I'd like to work up to the more advanced plants. What would you start with in a 72" high-tech tank, and what would you add later? And what fish do well in that setup?
  7. Water: I've always run RODI for the reef. For planted, do I use straight tap, RO with remineralizer, or a blend? Which GH and KH numbers should I be shooting for?
  8. Cycling: Plants change how you cycle, right? What's the order of operations?
Fair warning, I'm a gear nerd and I tend to wing it, so feel free to tell me when I'm about to do something dumb. I'll keep this thread updated as I go.

Any help or guidance would be appreciated.

Thank you!!!

Will be continued!
100 Replies · 2392 views
Noahspapa
I Donated 2026
Last reply · posted in Planted Aquarium Discussion
It’s time to take down the 20 gallon long tank that was my first “ high tech planted” aquarium and upgrade to a tank with on an appropriate size/depth.

I’ll order a Landen (90 x 50 x 50) tank on Amazon for this. Free overnight delivery. Preposterous!

I’ve studied the thread TRyan posted on 3/4” plywood stands and will be building a stand for this - thank you TRyan!

For filtration, I’ve been studying JayP’s thread. I had a biomaster thermo 350 on the 20L which I’m thinking of reusing. And I also have a netlea prefilter sitting around and an ARC small acrylic yugang reactor I can steal from a tank. I’m thinking of buying an Oase 800 or other pump and chaining these pieces together to provide a second filtration/carbonizing path? Not sure on the pump manufacturer & size?

I’ll be putting this together in the style of the ADA nature aquarium. Aquasoil in the back, some hardscape (rock, wood) in the midground and a decorative sand foreground. Very simple. Primarily a guppy, Endler, Cory, pleco, neocaridina tank.

Soliciting the scapecrunch community for feedback, advice, suggestions, etc.

Thank you as always. You all are the best!
43 Replies · 2719 views
Countrykingdom09
Last reply · posted in Journals
Hi. Have 3 tanks. 3 years of tank experience. 2 of keeping plants. I had some great success last year with all my plants, this year, ehh.

2 are cycled, the one is not but stores plants only. And a handful of bladder snails (rn at least).


10 Gallon planted WCMM tank:
Stocking: 6 wcmm, bladder snails
plants: Anubias, amazon sword, Val, dwarf sag, water sprite, moss ball, hornwort, and dwarf lily.
lighting and ferts: ACO EG ferts, nicrew light, nuthin to special. But it does the job. And working on A BUDGET.
HOB filter, PF sand. Rock planter for the anubias. Airstone. It has been set up for 2 years. Has had MANY MANY plants over that timeline!
20 Gallon planted community:
stocking: 6 harlequin rasboras, and bladder snails, ofc they hitchhiked lol.
plants: anubias, amazon sword, Val, dwarf sag, water wisteria, hornwort, moss ball, windelov java fern babies, tiger lotus.
lighting and ferts are the same.
Two sponge filters. PF sand. I plan to add more fish including...
honey Gourami
pygmy corydoras
green neon tetras
5 gallon hornwort tank:
Bladder snails, cheap topfin light, came with tank. Hornwort, a LEGO cave for fun lol. I grabbed the water from my 20 long. It was in storage for 2 plus years, but I have a LONGGGG story about my hornwort. It is not cycled.

More info later folks! Glad to be here, -whitecloud09
14 Replies · 2162 views
fishyjeff
Last reply · posted in Planted Aquarium Discussion
I noticed that MJAquascaping will be doing a seminar in Athens, GA. Here’s a link for anyone interested.

5 Replies · 181 views
renesis
Last reply · posted in Journals
Hi guys!

I'm new here, but not entirely new to planted tanks though I've been out of the hobby for the better part of the last decade between kids and moving a couple of times - but finally in a spot where I can do something again. I'm mostly going to be making things up as I go along, but plan on a lot of automation (I want to integrate everything into home assistant) and a lot of DIY as I love the challenge of building things out myself.

The starting point:

I picked up a 90P rimless, low-iron tank on a great deal.

Media (1).webp

I have a rough idea in my head for a stand to be built from plywood - just have a couple other house projects to finish off before starting that built.

Wife says I can only have one aquarium, so for this tank, I want to go all out with a sump to allow for auto top off, and auto water changes, auto fertilizer dosing etc. etc. I have half a plan in my mind.

I've also started on the light fixture which I've modeled up in CAD, and plan on making out of an 8020 extrusion, and some 3D printed bits.
Screenshot 2026-06-01 092809.webp
I'm using bridgelux gen 3 thrive CW (3000k) and WW (5000k) LED strips which have super high CRI at 98+ along with some specific XPE2 wavelengths that I'll solder onto some starboards. Far Red (730nm), Red (654nm), Cyan (495nm), Blue (455nm), Visible UV (415nm). Each segment of the white channels will be on its own driver so I can adjust left to right brightness in thirds, and each colour channel on its own driver so I can vary each channel on a time-based approach.

These will be run from a custom PCB board with Meanwell N-LDD drivers, and will run ESPHome on an ESP32 so it can link up with my Home Assistant installation.
1780321317096.webp

That's it for now, this will probably be a very slow build so be warned if you follow along!
102 Replies · 9396 views
Art
Art
Staff member I Donated 2026 Founding Member
· posted in Meet & Greet Forum

Hello  Welcome, gxtrex

Welcome to ScapeCrunch, @gxtrex!
We would love to get to know you. Please tell us about yourself. What tank do you have?
0 Replies · 15 views
Back
Top