Welcome to ScapeCrunch

We are ScapeCrunch, the place where planted aquarium hobbyists come to build relationships and support each other. When you're tired of doom scrolling, you've found your home here.

Journal Jay's 22 Long Iwagumi

JayP

Valuable Member
Joined
Jul 13, 2025
Messages
2,047
Reaction score
3,679
Location
Raymore, MO United States
I thought I would go ahead and get an early start on the journal for my next build. Still some prep work to complete but I was able to sneak some time in this evening to do some leak testing.

No need for a ton of media on this tank so I'll be using the "Temu" filters I recently talked about; one is a full foam prefilter and the other is part foam, part matrix. I failed to mention, when I posted my initial unboxing of the temu filters, that they do come in 2 sizes for each configuration, a 200 series, and the slightly larger 240 series. I think using the smaller 200 as the prefilter will work well in this setup. I was really surprised to see how much the foam expanded once it got wet. I may actually remove the top portion of foam in the filter with the matrix. Also, I confirmed the Netlea valves do work on the Temu filters.

I'm going with the MDP-2500 pump which may seem overkill for a 22g tank, but since it's 90cm in length, I want to make sure I have good flow end-to-end, and the 1500 pump I tried wasn't giving me quite what I wanted. I still also have to go through an inline heater as well, with several elbow fittings mixed in. I'll be able to adjust this pump down to just what I want. I'm also using the 3D printed barbs I modeled with the pump. I initially had issues with my elbow fittings leaking just as @renesis did on their high tech build. After seeing renesis's fix of coating the elbow with epoxy, I was about to try the same but realized I had a small can of spray-on Flex Seal so thought I'd give that a try. So far, it seems to be working fine on the elbow fitting. I do have a small leak on the output straight fitting but I think that's a different issue.

Otherwise, no other leaks which surprised me as I was expecting some on my DIY CO2 reactor which is a bit different design than my previous builds. It's working great and I want to give a shoutout to @Yugang for the idea of simply using some teflon sealing tape to seal the PVC caps to the Acrylic tube. You don't even need many wraps. I made the mistake of using too much on one end and when I tried to take it back off, it was quite a struggle, almost as if I had glued it, so trust me, as long as your cap I.D. matches your pipe O.D., a few wraps should do the trick.

More to come.


 
Last edited:
Looking forward to seeing this come together Jay. As for the leaking pump fittings, I encountered that also. I never got comfortable with the two-piece design on that style of pump. This solid fitting has worked well for me. They're also available as a straight barb.

45004390.jpg
 
Looking forward to seeing this come together Jay. As for the leaking pump fittings, I encountered that also. I never got comfortable with the two-piece design on that style of pump. This solid fitting has worked well for me. They're also available as a straight barb.

45004390.jpg
Not sure I follow how you're using those Apollo fittings. I've been able to use the pumps leak free by cobbling together various PVC parts, but the objective of the 3D printed fittings was to have a single piece 5/8 barb fitting. Jebao doesn't provide 5/8 fittings for their pumps larger than the 1500l/hr models. The thing I don't care for with those larger Jebao pumps, is they designed them with an o-ring in a channel rather than a flat lip and flat gasket like with their smaller pumps. The o-ring, of course, is fine if the pump is used submerged, but doesn't seal as reliably for external use.
 
Not sure I follow how you're using those Apollo fittings.
Just getting back to this in case anyone comes across it in the future. I hope the photo clarifies how I’m using the Apollo fittings. They are serving as a one piece hose barb. They’ve been leak free.
IMG_8188.webp
 
Just getting back to this in case anyone comes across it in the future. I hope the photo clarifies how I’m using the Apollo fittings. They are serving as a one piece hose barb. They’ve been leak free.
I'm surprised these screw on securely to the Jebao threads which are metric British Pipe or Proprietary. I looked over the other sizes of adapters they have and not sure they have a size that would work for anything above the 1000-1500 lph models.

I also still wasn't happy with my 3d printed fittings and having to coat them with epoxy or flex seal to prevent leaking. Pictured is the latest iteration of what I've decided to go with. I use stock Jebao 3/4 pipe fittings with a 3/4 spigot to 3/4 female npt fitting and a 3/4 male npt to 5/8 hose barb. The black Jebao pipe melts fast using standard PVC cement so you have to work precisely and quickly. The connection is holding strong and water tight though.

Also, the stock Jebao O-rings are leak free as long as I use silicone grease on them.

3/4" PVC Schedule 40 Spigot x Female Adapter

Jebao fittings.webp
 
I'm surprised these screw on securely to the Jebao threads which are metric British Pipe or Proprietary. I looked over the other sizes of adapters they have and not sure they have a size that would work for anything above the 1000-1500 lph models.

I also still wasn't happy with my 3d printed fittings and having to coat them with epoxy or flex seal to prevent leaking. Pictured is the latest iteration of what I've decided to go with. I use stock Jebao 3/4 pipe fittings with a 3/4 spigot to 3/4 female npt fitting and a 3/4 male npt to 5/8 hose barb. The black Jebao pipe melts fast using standard PVC cement so you have to work precisely and quickly. The connection is holding strong and water tight though.

Also, the stock Jebao O-rings are leak free as long as I use silicone grease on them.
If you are using adapters anyway, you could go with a vertically printed piece to replace the jebao and slip fitting piece, so you can screw the straight or npt adapter right into it.

I have a jecod ep-3500, if the fittings are the same, I can take a crack at designing a fitting for you if you'd like?
 

Top 10 Trending Threads

Back
Top